[Stijn D.C.]

Hello,


Since 1 of the last updates, the system for have right Ampérevalues on AMMETERS of cabview dont work anymore.

Before on .cvf, .eng file we must /100 for it

Example ( EMU )

Engined piece:

	Type 							( Electric )
	MaxPower 						( 735kW )
	MaxForce 						( 58.28kN )
	MaxContinuousForce 					( 58.28kN )
	MaxCurrent 						( 600A )

		Dial (
			Type ( AMMETER DIAL )
			Position ( 469 299 12 32 )
			Graphic ( AMPNEEDLE.ace )
			Style ( NEEDLE )
			ScaleRange ( 0 600 )
			ScalePos ( 270 360 )
			Units ( AMPS )
			Pivot ( 35 )
			DirIncrease ( 0 )
		)

Non Engined piece ( steeringcar )

	Type 							( Electric )
	MaxPower 						( 0.735kW )
	MaxForce 						( 0.5828kN )
	MaxContinuousForce 					( 0.5828kN )
	MaxCurrent 						( 6A )

		Dial (
			Type ( AMMETER DIAL )
			Position ( 469 299 12 32 )
			Graphic ( AMPNEEDLE.ace )
			Style ( NEEDLE )
			ScaleRange ( 0 6 )
			ScalePos ( 270 360 )
			Units ( AMPS )
			Pivot ( 35 )
			DirIncrease ( 0 )
		)

But now for moment the needle on steeringcars go directly too full value on first tractionstep...

I have this with all steeringcars and EMU cabines where no engine is installed.


In advance thanks for support.

[Weter]

Hello.
What if to try using not Engine, but CONTROL type for cab car, instead of dividing everything by 100, as in MSTS times?

Type (Control)

[Stijn D.C.]

Hello,

If i try that, i get cabview, can handle some controls, but Powerkey... not working... and train not wil depart.

Also Linevoltageneedle stay down.

[Weter]

That's for Peter ;)

[Stijn D.C.]

It is not the only thing,

Precision ( 10 )
UpdateTime ( 1.5 )

Dont work anymore too.

[Weter]

Quote

Precision ( 10 )
UpdateTime ( 1.5 )

I've only heared about "Accuracy" so far.
UpdateTime?! sounds cool.
Where can the full list of such new parameters be found?

[Stijn D.C.]

Hello,

This is for interval on cabviewcontrols, like speedneedle: ( Like Hasler TELOC speedneedles )

CabViewControls ( 1
Dial (
Type ( SPEEDOMETER DIAL )
Position ( 48 159 7 55 )
Graphic ( TELOC.ace )
Style ( NEEDLE )
ScaleRange ( 0 150 )
ScalePos ( 241.5 120 )
Units ( KM_PER_HOUR )
Pivot ( 42.5 )
DirIncrease ( 0 )
Precision ( 10 )
UpdateTime ( 1.5 )
)


For .CVF files you have "label", "ORTSLabel", "ORTSDisplay", "ORTSScreenPage", "ORTSCabviewPoint" too.

[Stijn D.C.]

And for some controls like gauches, there exist ORTSAngle too, for rotate the gauche.

[Weter]

Thanks.
Is Accuracy=Precision, Label=ORTSLabel?

[Stijn D.C.]

On the code they are independent in the list, but i can not said/confirm this 100%.


I'am not chur of this is written on manual/TechDocs also.