Hello,
For moment my overspeeddisplay shows onley when the train is 7km/h above the linespeed.
Is there a way for change that 7 km/h, so that i have indication on 4km/h above the linespeed or after 1km/h ?
So now it is config like this:
OverspeedMonitor(
MonitoringDeviceMonitorTimeLimit( 0 )
MonitoringDeviceAlarmTimeLimit( 1 )
MonitoringDevicePenaltyTimeLimit( 0 )
MonitoringDeviceCriticalLevel( 130 )
MonitoringDeviceResetLevel( 0 )
MonitoringDeviceAppliesFullBrake( 0 )
MonitoringDeviceAppliesEmergencyBrake( 0 )
MonitoringDeviceAppliesCutsPower( 0 )
MonitoringDeviceAppliesShutsDownEngine( 0 )
MonitoringDeviceTriggerOnTrackOverspeed( 1 )
MonitoringDeviceTriggerOnTrackOverspeedMargin( 2 )
MonitoringDeviceResetOnResetButton( 0 )
)
In advance thanks,
Page 1 of 1
Overspeeddisplay config OverspeedMonitor( Programming
#2
Posted 28 January 2019 - 02:55 PM
Stijn D.C., on 28 January 2019 - 02:18 AM, said:
Hello,
For moment my overspeeddisplay shows onley when the train is 7km/h above the linespeed.
Is there a way for change that 7 km/h, so that i have indication on 4km/h above the linespeed or after 1km/h ?
For moment my overspeeddisplay shows onley when the train is 7km/h above the linespeed.
Is there a way for change that 7 km/h, so that i have indication on 4km/h above the linespeed or after 1km/h ?
I believe by default, OR reads the monitor speed sections as M/S. If so, then :
MonitoringDeviceTriggerOnTrackOverspeedMargin( 2.000 )= 7.2km/h
MonitoringDeviceTriggerOnTrackOverspeedMargin( 1.111 )= 4km/h
MonitoringDeviceTriggerOnTrackOverspeedMargin( 0.277778 )= 1km/h
Thanks
#4
Posted 29 January 2019 - 05:03 AM
I usually fill it in as an example (4kmh) to get value in km / hours, also works.
#5
Posted 16 August 2019 - 01:57 AM
Hi All,
My overspeeddisplay shows when exceeding the line speed by a specified amount ( usually 2mph ). However the light only goes off when the speed drops to zero - is there a way of resetting the display to off when the speed drops below the line speed as is also shown by colour changes in the Track Monitor?
Regards,
Stephen
My overspeeddisplay shows when exceeding the line speed by a specified amount ( usually 2mph ). However the light only goes off when the speed drops to zero - is there a way of resetting the display to off when the speed drops below the line speed as is also shown by colour changes in the Track Monitor?
Regards,
Stephen
#6
Posted 17 August 2019 - 05:30 AM
Hi All,
I don't know quite I have done but the overspeed light is now working properly on a Class 465 EMU. I still need to test this on other types of motive power.
Following on from this I have added a digital speedometer and speedlimit display. How can I get these to change colour when exceeding the speed limit and back again when back to below the limit?
Any help will be gratefully received,
Stephen
I don't know quite I have done but the overspeed light is now working properly on a Class 465 EMU. I still need to test this on other types of motive power.
Following on from this I have added a digital speedometer and speedlimit display. How can I get these to change colour when exceeding the speed limit and back again when back to below the limit?
Any help will be gratefully received,
Stephen
Page 1 of 1