Elvas Tower: Western Pacific Route - Elvas Tower

Jump to content

  • 2 Pages +
  • 1
  • 2
  • You cannot start a new topic
  • You cannot reply to this topic

Western Pacific Route No tracks Rate Topic: -----

#1 User is offline   B & O GUY 

  • Vice President
  • Group: Status: Elite Member
  • Posts: 2,354
  • Joined: 14-May 08
  • Gender:Not Telling
  • Location:New York State
  • Simulator:Open Rails
  • Country:

Posted 01 June 2015 - 11:34 AM

I wanted to get this in here before I can't.

I was running the WP route from 3DTrains last night in Ver. 1. The only tracks showing are on long curves and bridges. Yards and straight sections don't show up at all. OR doesn't show any errors and trains glide over the dirt just as if the rails were present.

Allen

#2 User is offline   copperpen 

  • Executive Vice President
  • Group: Status: Elite Member
  • Posts: 3,144
  • Joined: 08-August 05
  • Gender:Male
  • Simulator:MSTS & OR
  • Country:

Posted 01 June 2015 - 12:36 PM

I just loaded the Feather River to check, started in Portola and had tracks everywhere I looked. What is your LOD slider set to. Mine is dead centre.

#3 User is offline   timmuir 

  • Member since Nov. 2003
  • Group: Status: Elite Member
  • Posts: 9,513
  • Joined: 22-November 03
  • Gender:Not Telling
  • Location:Somewhere on the Beautiful Oregon Coast
  • Simulator:Open Rails Only
  • Country:

Posted 01 June 2015 - 12:36 PM

Was this at any particular spot, Allen? Or everywhere? I just did a quickie test from Portola using Derek's big WP Northern 481 and didn't experience anything out of the ordinary.

Attached Image: Open Rails 2015-06-01 01-28-30.jpg

#4 User is offline   B & O GUY 

  • Vice President
  • Group: Status: Elite Member
  • Posts: 2,354
  • Joined: 14-May 08
  • Gender:Not Telling
  • Location:New York State
  • Simulator:Open Rails
  • Country:

Posted 01 June 2015 - 12:40 PM

Where do I find that? LOD slider. Never mind I found it. It's set to dead center. 0%

Allen

#5 User is offline   B & O GUY 

  • Vice President
  • Group: Status: Elite Member
  • Posts: 2,354
  • Joined: 14-May 08
  • Gender:Not Telling
  • Location:New York State
  • Simulator:Open Rails
  • Country:

Posted 01 June 2015 - 12:45 PM

Tim. I started at Orinor. I think that's what they call it.

Allen

#6 User is offline   copperpen 

  • Executive Vice President
  • Group: Status: Elite Member
  • Posts: 3,144
  • Joined: 08-August 05
  • Gender:Male
  • Simulator:MSTS & OR
  • Country:

Posted 01 June 2015 - 12:47 PM

So what does your OR log have to say.

#7 User is offline   B & O GUY 

  • Vice President
  • Group: Status: Elite Member
  • Posts: 2,354
  • Joined: 14-May 08
  • Gender:Not Telling
  • Location:New York State
  • Simulator:Open Rails
  • Country:

Posted 01 June 2015 - 12:56 PM

Here you go.Attached File  OR-lopg.zip (44.2K)
Number of downloads: 141

Allen

#8 User is offline   Hack 

  • Engineer
  • Group: Status: Active Member
  • Posts: 738
  • Joined: 23-November 03
  • Gender:Male
  • Location:Another Planet
  • Country:

Posted 01 June 2015 - 01:49 PM

Do you have ScaleRail installed?

#9 User is offline   B & O GUY 

  • Vice President
  • Group: Status: Elite Member
  • Posts: 2,354
  • Joined: 14-May 08
  • Gender:Not Telling
  • Location:New York State
  • Simulator:Open Rails
  • Country:

Posted 01 June 2015 - 02:04 PM

Er a Maybe. Yes! It's an upgrade to the Pokey route. That works okay. I've run that on the new version 1. Does that help. I have the regular WP install disc. Wouldn't it be on that and included with the install. If I remember it asks a question or two when installing.

I installed it three or four years ago. Might it need to be refreshed. I've got a lot of stuff on this old computer.

Allen

#10 User is offline   Hack 

  • Engineer
  • Group: Status: Active Member
  • Posts: 738
  • Joined: 23-November 03
  • Gender:Male
  • Location:Another Planet
  • Country:

Posted 01 June 2015 - 07:59 PM

Reinstall the route and see if that solves things.
  • 2 Pages +
  • 1
  • 2
  • You cannot start a new topic
  • You cannot reply to this topic

1 User(s) are reading this topic
0 members, 1 guests, 0 anonymous users