[engmod]

Hi Team,

Player Train.Lead Locomotive must be Player Locomotive crash with only box on screen.

Crash is reproducable.
While making up a train after a reverse point, I had collected 3 cars, then connected to an RDC.

Attached thumbnail(s)

• 

Attached File(s)

•  DARv3_Kentville Yard 2022-03-28 13.29.18.txt (12.26K)
  Number of downloads: 150

[Csantucci]

Hi Derek,
what is an RDC?
When exactly does the crash occur? When you connect to the "RDC"?

[R H Steele]

Carlo it is a Budd Rail Diesel Car
Derek, are you using the RDC's Paul made for OR or the MSTS set?

[Laci1959]

Hello

Similar two-axle vehicles were delivered by the Budapest GANZ plant in 1932 to the Ferrovia Monza-Molteno-Oggione railway in northern Italy. The Santerno Anonima Ferroviaria railway also bought such motor cars with its trailers. A S.A.F. The M52 was stopped in 1987 because it could not replace the original KNORR transmission.

Sincerely, Laci 1959

[engmod]

Csantucci, on 28 March 2022 - 05:56 AM, said:

Hi Derek,
what is an RDC?
When exactly does the crash occur? When you connect to the "RDC"?

It happened when I set to reverse and tried to take off.

https://en.wikipedia...Rail_Diesel_Car

I believe the RDC that Paul has used here goes back to BLW.

[Csantucci]

Is DAR a freely downloadable route?

[engmod]

Yes, Carlo

https://www.trainsim...right&fid=35520

[Csantucci]

Thank you. I have now downloaded and installed route and rolling stock. I have this endless workorder in front of me (Darv3 Kentville Yard.txt) :sweatingbullets: . May I know at which step the crash occurs? Even better, can you list the sequence of switching steps you did to provoke the crash? And what does "Switch 26 and make up 24" mean? BTW the player loco brakes very, very slowly. Sorry for the many issues.

[engmod]

Hi Carlo,

MG 121

I have done a save just before coupling to the RDC, you may wish to try this before you run the complete activity part.

26 and 24 I don't know, doesn't seem to be needed.

1. move forward to the reverse point,
2. let OR reverse direction,
3. notice that there is no path, go to manual,
4. when you get out of control on track monitor, go to manual again to reset,
5. move backwards
6. there is a facing point onto the RDC, this is not the path we need, reset the point to the straight,
7. the point onto the RDC will not change to the straight, I have to enter the siding then reverse out and then the point will change,
8. moving backwards, the next point is the one that we need to pick up a guards van,
9. pick up van, go forward, back to the lead you came out of,
10 moving up the lead, you want the left track at the next point to get to the ice house,
11 pull out 2 cars, the one you want is the second, push it up towards jamison as that is the next pickup,
12 push the flat car back to the ice house,
13 back to the jamison siding to pick up the box car and the car in jamison,
14 back out to the main line,
15 backwards towards the centre of town ( towards the RDC ),
16 if you stop just before the point onto the RDC, you will notice that track monitor shows end of path ( in manual mode ), and the switch monitor shows a path set ( in manual mode )
17 move to the RDC
18 I connected to the RDC, moved forwards, no crash,
19 pushed the RDC back in the siding,
20 went to uncouple, crash

21 the debugger opened up Visual Studio, but no code came up, so I do not have it configured correctly.

Attached thumbnail(s)

• 
• 

Attached File(s)

•  Darv3_kentville yard 2022-04-02 09.43.16.zip (2.55MB)
  Number of downloads: 142
•  DARv3_Kentville Yard 2022-04-02 09.43.16.txt (12.19K)
  Number of downloads: 137

[Csantucci]

Thanks Derek,
I greatly appreciate your effort. Unfortunately at the moment in general saves on a computer don't work on another one. I'll however try to change this, to avoid alls shunting.