[Laci1959]

comment (
M44 menetfokozat kiosztasa: [6/165]
Fokozat	Ford.sz. (1/min)	Teljesitmeny (kW)
0	550	(0)		0	(0)
S	900	(0.818)		0	(0)
X	900	(0.818)		0	(0)
1a	800	(0.727)		100	(0.27)
1b	800	(0.727)		100	(0.32)
1c	800	(0.727)		100	(0.34)
1d	800	(0.727)		100	(0.36)
2	845	(0.768)		146	(0.394)
3	880	(0.8)		190	(0.513)
4	930	(0.845)		231	(0.624)
5	970	(0.881)		252	(0.681)
6	1005	(0.913)		288	(0.778)
7a	1025	(0.931)		330	(0.891)
7k	1100	(0.1)		370	(1)	
)

Throttle notches for the M44 370kW diesel electric reversing locomotive. I was wrong, there were only two air producing stages. The first stage consisted of four notches. Unfortunately, I don't know the reason. The table was made back in the MSTS days.

[darwins]

I can see a problem with those settings in OR. Diesel engine rpm tab always has to have increasing rpm, never decreasing. I had a similar problem with one of the British diesel electrics. http://www.elvastowe...post__p__258303

[Laci1959]

darwins, on 25 September 2022 - 12:50 AM, said:

I can see a problem with those settings in OR. Diesel engine rpm tab always has to have increasing rpm, never decreasing. I had a similar problem with one of the British diesel electrics. http://www.elvastowe...post__p__258303

That's right, that's why I left those settings. Once there is a P position at the flow valve, I will use it. Until then, it's in the comments.
I struggled a lot before I realized it. I don't understand why such constraints have to be brought into it, but it is what it is, it has to be used.
I saw that there is a control car with Type (Control) setting. It is very good. I also tried the energy-free control car with an electric locomotive. It worked perfectly, only the switches, lights, and instruments required for electric traction did not work. I hope one day Peter will complete it, that way it would be complete.

[darwins]

Laci1959, on 25 September 2022 - 02:58 AM, said:

I saw that there is a control car with Type (Control) setting. It is very good. I also tried the energy-free control car with an electric locomotive. It worked perfectly, only the switches, lights, and instruments required for electric traction did not work. I hope one day Peter will complete it, that way it would be complete.

Perhaps we can put together a list of things that work and things that do not work to help future development.
I have tried to do this on the Control Trailer thread. You may want to check if you agree with my findings. http://www.elvastowe...post__p__288999

[Laci1959]

darwins, on 25 September 2022 - 07:06 AM, said:

Perhaps we can put together a list of things that work and things that do not work to help future development.
I have tried to do this on the Control Trailer thread. You may want to check if you agree with my findings. http://www.elvastowe...post__p__288999

Thanks, I'll definitely try this. I will write my findings there.

[Laci1959]

Hello.

The manual gearbox does not work with the AI train. The OR freezes. Can this bug be fixed?
LOG file attached.
I tried it with the corresponding CTN test locomotive and with my own locomotive. If I'm driving the locomotive, it's fine, if I want to use it as an AI train for a task, it freezes.

Sincerely, Laci1959

LOG

[steamer_ctn]

Laci1959, on 08 April 2024 - 10:03 AM, said:

LOG file attached.

Whilst I appreciate that English is not your first language, sadly it is my only language, so could you run OR in English (as a temporary measure) when you produce the LOG file so that I can read it without trying to play around with translators?

[Laci1959]

Hello.

The requested log file is in English.
I made a simple two-cylinder steam locomotive. The smoke effect and the tired steam effect coming out of the cylinders also work nicely.
BUT.
If the AI works as a train in a task, the tired steam effect disappears. Since it doesn't cause freezing, I don't care.

Best regards, Laci 1959

LOG file

[steamer_ctn]

Laci1959, on 08 April 2024 - 10:31 PM, said:

The requested log file is in English.

Thanks for that.

There appears to be at least one error in the ENG file that should be fixed first to see if it is contributing to the problem.

Warning: Expected depth 0; got depth 1 at end of file (missing ')'?) in D:\Train Simulator\trains\trainset\Triglav\Triglav.eng:line 646  

 Warning: System.IO.FileLoadException: D:\Train Simulator\trains\trainset\Triglav\Triglav.eng ---> System.IO.InvalidDataException: D:\Train Simulator\trains\trainset\Triglav\Triglav.eng  

Engine type missing

Have a look at line 646 of your ENG file and see if you can fix it.

If you are able to fix the ENG file problems, and this doesn't fix your original problem, then set up a simple small activity using CTN stock to demonstrate the issue. Then I can see the problem that you are experiencing.

Laci1959, on 08 April 2024 - 10:31 PM, said:

I made a simple two-cylinder steam locomotive. The smoke effect and the tired steam effect coming out of the cylinders also work nicely.
BUT.
If the AI works as a train in a task, the tired steam effect disappears. Since it doesn't cause freezing, I don't care.

This seems to be a bit off topic.

AI trains don't follow all the physics that a Player train adheres to, so it could be that the AI train is ignoring these physics.

[Laci1959]

Hello.

The Trigav was a steam locomotive. It was deposited as LOOSE consist. I removed it from Activity and the error still exists. I will provide the corrected log file.
Thanks for alerting me to the error.

The replaced LOG file