Log In
Register Now!
Help
Working on removal of this bug https://bugs.launchp...or/+bug/1497429 I have noticed that also Curtius-Kniffler parameters customized within .eng file had no effect (the default values were used anyhow). This has been solved in release x.3259.
Customized Curtius-Kniffler parameters have no effect
Rate Topic:
#1
- Member, Board of Directors
-
- Group: Status: Elite Member
- Posts: 6,996
- Joined: 31-December 11
- Gender:Male
-
Country:
Posted 19 September 2015 - 10:13 AM
#2
- Superintendant
-
- Group: Status: Elite Member
- Posts: 1,313
- Joined: 18-June 14
- Gender:Male
- Location:West of the Contental Divide
- Simulator:ORTS_Running MSTS_Editing
-
Country:
Posted 19 September 2015 - 12:37 PM
Carlos,
Watching you and others on the team chop through these bugs is sooo wonderful (impressive too!) after the years of non-response from the KUJU-Micro$oft cabal and our cry for at the least to provide us with some meaningful documentation.
As I recall it took about a year just to find out how to make a terrain poly invisible (for a tunnel entrance) by a simple tap of the 'V' key.
:sign_thanks: so very much to all of you.
Sincerely,
vince cockeram
Watching you and others on the team chop through these bugs is sooo wonderful (impressive too!) after the years of non-response from the KUJU-Micro$oft cabal and our cry for at the least to provide us with some meaningful documentation.
As I recall it took about a year just to find out how to make a terrain poly invisible (for a tunnel entrance) by a simple tap of the 'V' key.
:sign_thanks: so very much to all of you.
Sincerely,
vince cockeram
#3
- Apprentice
-
- Group: Status: Active Member
- Posts: 48
- Joined: 05-January 14
- Gender:Male
- Simulator:MSTS
-
Country:
Posted 28 September 2015 - 10:45 AM
Hi All,
I just checked the adaptation of the Curtius-Kniffler Parameters and did not see any effect.
I tried the following Statements in the wagon section of the .eng file:
Wagon ( OR_Adhesion ( Curtius_Kniffler (7.5 44 0.861 0.7 ) ) )
and
Wagon ( ORTSAdhesion ( ORTSCurtius_Kniffler (7.5 44 0.861 0.7 ) ) )
At the start the electric loc with a mass of 86t provided ist Maximum tractive force of 300 kN. But at 15 km/h I observed wheel slip. This is a bit funny since the Default paramters (7.5 44 0,161 0.7) should give 279 kN of tractive force at start. With a C Parameter of 0.861 I should not get any slip. The advanced adhesion model was deactivaed. OR Version X.3264 was used.
Regards
Gehe
I just checked the adaptation of the Curtius-Kniffler Parameters and did not see any effect.
I tried the following Statements in the wagon section of the .eng file:
Wagon ( OR_Adhesion ( Curtius_Kniffler (7.5 44 0.861 0.7 ) ) )
and
Wagon ( ORTSAdhesion ( ORTSCurtius_Kniffler (7.5 44 0.861 0.7 ) ) )
At the start the electric loc with a mass of 86t provided ist Maximum tractive force of 300 kN. But at 15 km/h I observed wheel slip. This is a bit funny since the Default paramters (7.5 44 0,161 0.7) should give 279 kN of tractive force at start. With a C Parameter of 0.861 I should not get any slip. The advanced adhesion model was deactivaed. OR Version X.3264 was used.
Regards
Gehe
#4
- Member, Board of Directors
-
- Group: Status: Elite Member
- Posts: 6,996
- Joined: 31-December 11
- Gender:Male
-
Country:
Posted 28 September 2015 - 11:45 AM
Curtius-Kniffler works only with advanced adhesion.
#5
- Apprentice
-
- Group: Status: Active Member
- Posts: 48
- Joined: 05-January 14
- Gender:Male
- Simulator:MSTS
-
Country:
Posted 29 September 2015 - 07:49 AM
Thanks for the quick reply!
#6
- Apprentice
-
- Group: Status: Active Member
- Posts: 48
- Joined: 05-January 14
- Gender:Male
- Simulator:MSTS
-
Country:
Posted 30 September 2015 - 10:05 AM
Hi All,
I did some tests with a diesel and an electric loco and still I do not observe any effect when I Change the Curtius-Kniffler parameters, maybe I do something wrong in the .eng
Regards
Gehe
I did some tests with a diesel and an electric loco and still I do not observe any effect when I Change the Curtius-Kniffler parameters, maybe I do something wrong in the .eng
Regards
Gehe
#7
- Apprentice
-
- Group: Status: Active Member
- Posts: 48
- Joined: 05-January 14
- Gender:Male
- Simulator:MSTS
-
Country:
Posted 01 October 2015 - 09:57 AM
Hi All,
problem solved looks like that ORTS does not accept all the options as indicated in the Manual:
ORTSAdhesion (
ORTSCurtius_Kniffler (
7.5
44
0.161
0.7
)
)
works.
Regards
Gehe
problem solved looks like that ORTS does not accept all the options as indicated in the Manual:
ORTSAdhesion (
ORTSCurtius_Kniffler (
7.5
44
0.161
0.7
)
)
works.
Regards
Gehe
#8
- Member, Board of Directors
-
- Group: Status: Elite Member
- Posts: 6,996
- Joined: 31-December 11
- Gender:Male
-
Country:
Posted 01 October 2015 - 10:56 AM
Hi Gehe,
can you tell us pls. what options OR does not accept, so that we can correct the manual?
can you tell us pls. what options OR does not accept, so that we can correct the manual?
#9
- Executive Vice President
-
- Group: Status: Elite Member
- Posts: 3,143
- Joined: 08-August 05
- Gender:Male
- Simulator:MSTS & OR
-
Country:
Posted 01 October 2015 - 11:10 AM
Looking at the last post from Gehe. it is the format of the data. In the manual this is in one horizontal line. In the post from Gehe the working version is vertical with each data segment on its own line.
#10
- Apprentice
-
- Group: Status: Active Member
- Posts: 48
- Joined: 05-January 14
- Gender:Male
- Simulator:MSTS
-
Country:
Posted 02 October 2015 - 07:48 AM
Could be, because the options which did not work are also in one horizontal line.
Look at my posting on 28.9.2015 07:45 pm.
Gehe
Look at my posting on 28.9.2015 07:45 pm.
Gehe